Featuring a larger capacity than our standard ditching bucket, the Craig Clean Up Bucket is ideal for cleaning out established ditches that have become overgrown over the years. Equipped with drain holes for working in wet environments, this bucket can be equipped with either a straight or a serrated cutting edge for badly overgrown ditches.

• Cutting edge is reversible and replaceable
• Available in Wedge Lock, Pin-on, S Series, or Manual Bar Lock lugging
• Comes pre-drilled for bolt-on cutting edge
• Tapered shell profile for easy loading and dumping
• Horizontal wear bars standard

With a wide, shallow, smooth curl design – this bucket is ideal for cleaning ditches, grading, and aggregate work. Equipped with drain holes for working in wet environments, this bucket can be equipped with either a straight or a serrated cutting edge for badly overgrown ditches.

• Cutting edge is reversible and replaceable
• Available in Wedge Lock, Pin-on, S Series, or Manual Bar Lock lugging
• Comes pre-drilled for bolt-on cutting edge
• Tapered shell profile for easy loading and dumping
• Horizontal wear bars standard

With its low profile design, curved cheek plates and active attack angle, the Craig Quik Fill bucket is designed to minimize surface friction and maximize cycle time efficiency when loading and unloading the bucket.

The lengthened shell floor promotes smooth loading and unloading with minimal wasted movement. Instead of using breakout force to fill the bucket by curling the attachment, the Quik Fill bucket is designed to be pulled towards the machine – shaving material into the bucket in a smooth motion. This motion eliminates partial fills and excess spillage while also leaving the bucket closer to the open position to allow quicker dumping of the material.

• Available in Wedge Lock, Pin-on, S Series, or Manual Bar Lock lugging
• Longer hooks for easier alignment

Designed to ditch and grade at the same time, the Craig Trapezoid Ditching Bucket will save you time and money by allowing for fewer digging cycles than your traditional Ditching Bucket.

• Cutting edge is reversible and replaceable
• Weld on adapters and teeth available (optional)
• Available in Wedge Lock, Pin-on, S Series, or Manual Bar Lock lugging
• 30° wedge standard. Custom configurations available upon request

The Craig Hydraulic Angling Clean Up Bucket features a flat bottom design with angled cylinders, to prevent material build up, that offers up to 45° of rotation left and right. Available with a straight or serrated cutting edge.

• Top quality high tensile and abrasion resistant steel construction
• Available in Wedge Lock, Pin-on, S Series, or Manual Bar lock lugging
• Comes pre-drilled for bolt-on cutting edge
• No kickstand required - HACL buckets stand on their own
• Angled cylinders to help prevent material build up
• Flow control value to fine tune speed of bucket swing

The Craig Hydraulic Angling Ditching Bucket has a flat cylinder design to keep the tip radius to a minimum. This design allows for a full 45° of rotation while guarding the cylinders for maximum protection.

• Work quicker, on proper grade, without moving the machine
• Main hinge tilt pins are align bored for long life
• Available in Wedge Lock, Pin-on, S Series, or Manual Bar Lock lugging
• Comes pre-drilled for bolt-on cutting edge

This heavy-duty version of our Craig Hydraulic Angling Ditching Bucket is the perfect tool for all your ditching, grading, and contouring needs. The Craig Severe Service Hydraulic Angling Ditching bucket features a complete bucket weldment of Brinell 400 steel, Brinell 450 cheek plates, and hardened bushings at all pivot points.

• 42.5-degree rotation in both directions
• Available in Wedge Lock, Pin-on, S Series, or Manual Bar Lock lugging
• Comes pre-drilled for bolt-on cutting edge
• Available for 8 ton to 40 ton excavators
• Optional central greasing system available
• Optional cylinder covers available

The rock slab bucket expertly gets under layers of rock to break and remove chunks and slabs of rock. The half arrow tip and smooth edge makes it easy to slip between layers of rock to pry and lift slabs.

• Made entirely of high strength and high wear plate
• Continuous/solid plate design from hookup to the underside of the smooth edge for maximum strength.